Thank you!
We will contact you shortly.
Starting Guide Atom Carbon +R3
Atom Carbon +R3
He is a "heavyweight" in the Atom team. Designed to control powerful loads, as it is equipped with relay outputs with switching currents of 16 A and 26 A. You will not only be able to turn on powerful devices, but also conveniently organize controlled sockets for equipment with high starting currents.
Modifications
Functional elements
1. 9-48V DCPower supply
2. CAN bus ensures synchronized operationof all Atom series devices
3. Integrate 3rd party devicesusing RS-485 interface
4. 5V and 3.3V portsfor sensors power supply
5. 22 multifunction input ports (16 in N modification)for temperature, air quality, water leakage sensors and switches connection
6. Buttonsfor navigation and control of the OLED display menu
7. Graphic OLED displayfor control and monitoring (optional for N modification)
8. Ethernet port for network connectionpossibility of remote control using the phone or voice assistants (N modification)
Outputs
1. Energy meter with the ability to accurately measure voltage, current and power consumption
2. 2 x 5A relaysfor connection of electrical devices
3. 6 x 16A relays for connection of electrical devices
4. 3 x 26A relays for connection of electrical devices
LED Indication
1. Device status indication
2. LAN connection indication
3. Relay output ports indication
4. Output ports type and status indication
Technical specifications
Note : Technical specifications, wiring diagrams, input and output specifications and other technical information can be viewed on page Atom Carbon +R3
Installation guide
Important! During installation and operation, observe the general rules of electrical safety regarding the use of electrical appliances, as well as the requirements of regulations on electrical safety. It is strictly forbidden to disassemble a device to which any conductors are connected!
Important! Although the controller has built-in protection against incorrect power connection, and in this situation will not fail, we recommend that you pay attention to the correct polarity when connecting.
3. i3-NET
If your system uses multiple controllers, connect them to a i3-NET network. Install the end terminators included in the equipment kit at the ends of the bus.
4. RS-485
If you have Modbus controled devices, connect them to the bus and connect them to the RS-485 connector. Install the end terminators included in the equipment kit at the ends of the bus.
5.Sensors power supply
A 5V and 3.3V controller outputs are provided to power the sensors.
Important! If the system uses sensors or actuators with other operating voltages, use additional power supplies or the power supply that powers the controller. If the system uses several power supplies - connect their "negative" terminals to each other.
6. Input connections
Connect sensors, switches and other devices to the controller inputs. The inputs of the controller use connectors with spring-loaded contacts, which provides convenience and reliability of connection of conductors with a cross-section up to 1.5 mm2.
Atom Carbon +R3
TYPE OF INPUT / # OF INPUT
1-2
3-11
12-16
17-22
TYPE OF INPUT / # OF INPUT
TYPE OF INPUT / # OF INPUT
1-2
1-2
3-11
3-11
12-16
12-16
17-22
17-22
Analog (thermistor, photoresistor, etc.)
✖
✔
✖
✖
TYPE OF INPUT / # OF INPUT
Analog (thermistor, photoresistor, etc.)
1-2
✖
3-11
✔
12-16
✖
17-22
✖
Digital (motion sensors, light level sensors, switches, buttons, etc.)
✔
✔
✔
✔
TYPE OF INPUT / # OF INPUT
Digital (motion sensors, light level sensors, switches, buttons, etc.)
1-2
✔
3-11
✔
12-16
✔
17-22
✔
Interface (1-Wire sensors)
✔
✔
✖
✖
TYPE OF INPUT / # OF INPUT
Interface (1-Wire sensors)
1-2
✔
3-11
✔
12-16
✖
17-22
✖
Atom Carbon N +R3
TYPE OF INPUT / # OF INPUT
1-2
3-11
12-16
TYPE OF INPUT / # OF INPUT
TYPE OF INPUT / # OF INPUT
1-2
1-2
3-11
3-11
12-16
12-16
Analog (thermistor, photoresistor, etc.)
✖
✔
✖
TYPE OF INPUT / # OF INPUT
Analog (thermistor, photoresistor, etc.)
1-2
✖
3-11
✔
12-16
✖
Digital (motion sensors, light level sensors, switches, buttons, etc.)
✔
✔
✔
TYPE OF INPUT / # OF INPUT
Digital (motion sensors, light level sensors, switches, buttons, etc.)
1-2
✔
3-11
✔
12-16
✔
Interface (1-Wire sensors)
✔
✔
✖
TYPE OF INPUT / # OF INPUT
Interface (1-Wire sensors)
1-2
✔
3-11
✔
12-16
✖
Important! The inputs are numbered, and several terminals are marked with a "common" terminal (marked with the letter "G") - this is a common contact, it is connected to the "minus" power supply of the controller. All common contacts are interconnected, so when connecting switches with a lot of wired cable, if necessary, it is enough to use only one connection to the "G" terminal.
OUT7-OUT8 - relay outputs with switching current up to 5A (active load), designed for switching DC and AC loads with voltage up to 250V.
They are best suited for controlling low-power loads: thermal heads, LED lamps and luminaires up to 10 W, devices with dry contact inputs (garage doors, impulse blinds), intermediate relays, emergency lighting, electric locks.
AC IN and AC OUT connectors - energy meter input and output connections. The built-in energy meter is designed to control the voltage, current consumption and power of devices connected to the AC OUT connector. Controlled voltage range 170 - 250V, current - up to 10A.
OUT9-OUT11 - relay outputs with switching current up to 26A (active load), designed for switching DC and AC loads with voltage up to 250V.
Outputs are designed to connect heavy loads: lighting groups, controlled sockets, power supply input groups.
8. Network connection (modification N)
The operation of network controllers requires remote access to configure, manage and control their operation. To ensure these capabilities, at least one of the controllers must be able to connect to a wired or wireless network. In the Atom product line, these are the N modification controllers. Don't forget to connect the network cable to the controller or configure access to the home Wi-Fi network .
Important! The router must have a DHCP server configured to automatically issue the IP address and network mask.
9. Done. Turn on the power
Important! Check all connections. Make sure that the power supply, inputs and outputs are connected correctly.
10. i3 Home App configuration
After turning on the controller, you need to download the i3 Home mobile application and configure the system.
List of typical problems and their solutions
LED indicators do not light
1. Check the supply voltage on the controller
2. Check the polarity of the power supplyThe device is turned on but not in the application settings
1. Make sure Wi-Fi and bluetooth are turned on on your smartphone or tablet2. Verify that the home network password is specified correctly in the controller settings
Inputs do not respond to signals from sensors or switches
1. Check that the connection is correct2. Check that the connections at the controller and sensor terminals are secure3. Check the login configuration to the type of sensor or switch
Output status indicators are not lit
Check that the output settings are correct in the controller settings
The output status indicator lights up, the device does not turn on, or responds incorrectly
1. Check that the connection is correct and reliable2. Check the device for damage
Didn’t find the answer to your question?
You can contact the technical support chatbot.Found a mistake on the site? Help us fix it!