Starting Guide Xenon

Atom Xenon

Provides the ability to change the level of illumination of LED, halogen and incandescent lamps, both individually and in groups (up to 300W per channel). In addition to light control, Atom Xenon is perfect for controlling the following devices: garage doors, electric locks, actuators, and others.

Atom

Basic version

Atom N

Connect wireless devices and enjoy the remote control access

OLED-display

Optional for Atom NConfigure and diagnose devices even without internet connection

1. 9-48V DCPower supply

2. CAN bus ensures synchronized operationof all Atom series devices

3. Integrate 3rd party devicesusing RS-485 interface

4. 5V and 3.3V portsfor sensors power supply

5. 12 multifunction input ports (9 in N modification) for temperature, air quality, water leakage sensors and switches connection

6. Buttons for navigation and control of the OLED display menu

7. Graphic OLED displayfor control and monitoring (optional for N modification)

8. Ethernet port for network connectionPossibility of remote control using the phone or voice assistants (N modification)

1. 4 x 5A relaysfor connecting electrical appliances

2. 6 x MOSFET based dimmers with built-in load monitoring sensorsto control AC loads

1. Input ports indication

2. Device status indication

3. LAN connection indicationfor modification N

4. Relay output ports indication

5. Output ports type and status indication

Note : Technical specifications, wiring diagrams, input and output specifications and other technical information can be viewed on page Atom Xenon

Important! During installation and operation, observe the general rules of electrical safety regarding the use of electrical appliances, as well as the requirements of regulations on electrical safety. It is strictly forbidden to disassemble a device to which any conductors are connected!

Important! Although the controller has built-in protection against incorrect power connection, and in this situation will not fail, we recommend that you pay attention to the correct polarity when connecting

If your system uses multiple controllers, connect them to a i3-NET network. Install the end terminators included in the equipment kit at the ends of the bus.

Connect sensors, switches and other devices to the controller inputs. The inputs of the controller use connectors with spring-loaded contacts, which provides convenience and reliability of connection of conductors with a cross section up to 1.5 mm2.

TYPE OF INPUT / # OF INPUT
1-2
3-9
10-12

TYPE OF INPUT / # OF INPUT
TYPE OF INPUT / # OF INPUT

10-12
10-12

Analog (thermistor, photoresistor, etc.)
✖
✔
✔

TYPE OF INPUT / # OF INPUT
Analog (thermistor, photoresistor, etc.)

10-12
✔

Digital (motion sensors, light level sensors, switches, buttons, etc.)
✔
✔
✔

TYPE OF INPUT / # OF INPUT
Digital (motion sensors, light level sensors, switches, buttons, etc.)

10-12
✔

Interface (1-Wire sensors)
✔
✔
✔

TYPE OF INPUT / # OF INPUT
Interface (1-Wire sensors)

10-12
✔

TYPE OF INPUT / # OF INPUT
1-2
3-9

TYPE OF INPUT / # OF INPUT
TYPE OF INPUT / # OF INPUT

Analog (thermistor, photoresistor, etc.)
✖
✔

TYPE OF INPUT / # OF INPUT
Analog (thermistor, photoresistor, etc.)

Digital (motion sensors, light level sensors, switches, buttons, etc.)
✔
✔

TYPE OF INPUT / # OF INPUT
Digital (motion sensors, light level sensors, switches, buttons, etc.)

Interface (1-Wire sensors)
✔
✔

TYPE OF INPUT / # OF INPUT
Interface (1-Wire sensors)

Dangerous interference can occur on long lines when connecting end devices such as switches, so we use additional protection and improved sensitivity of interaction with end devices. We use optocouplers for this. By default, all inputs with jumpers are configured in this mode "Optocoupler". If you use digital sensors at the inputs of the controller, be sure to turn off this mode

The operation of network controllers requires remote access to configure, manage and control their operation. To ensure these capabilities, at least one of the controllers must be able to connect to a wired or wireless network. In the Atom product line, these are the N modification controllers. Don't forget to connect the network cable to the controller or configure access to the home Wi-Fi network

After turning on the controller, you need to download the i3 Home mobile application and configure the system.

LED indicators do not light
1. Check the supply voltage on the controller2. Check the polarity of the power supply
The device is turned on but not in the application settings
1. Make sure Wi-Fi and bluetooth are turned on on your smartphone or tablet2. Verify that the home network password is specified correctly in the controller settings
Input indicators do not respond to signals from sensors or switches
1. Check that the connection is correct2. Check that the connections at the controller and sensor terminals are secure3. Check the login configuration to the type of sensor or switch
Output status indicators are not lit.
Check that the output settings are correct in the controller settings
The output status indicator lights up, the device does not turn on, or responds incorrectly
1. Check that the connection is correct and reliable2. Check the device for damage