Thank you!
We will contact you shortly.
Starting Guide Atom Barium
Atom Barium
Solutions for control of lighting devices using DALI protocol. Allows you to turn on and adjust the brightness of up to 64 lights with the appropriate interface.
Modifications
Functional elements
1. 9-48V DCPower supply
2. CAN bus ensures synchronized operationof all Atom series devices
3. Integrate 3rd party devicesusing RS-485 interface
4. 3.3V portfor sensors power supply
5. 12 multifunction input ports (9 in N modification) for temperature, air quality, water leakage sensors and switches connection
6. Buttons for navigation and control of the OLED display menu
7. Graphic OLED displayfor control and monitoring (optional for N modification)
8. Ethernet port for network connectionPossibility of remote control using the phone or voice assistants (N modification)
Outputs
1. 3 x 5A relays for connection of electrical devices
2. DALI for connection and control of devices using DALI protocol
LED indications
1. Input ports indication
2. Device status indication
3. LAN connection indicationfor modification N
4. Output ports indication
Technical specifications
Note : Technical specifications, wiring diagrams, input and output specifications and other technical information can be viewed on page Atom Barium
Installation guide
Important! During installation and operation, observe the general rules of electrical safety regarding the use of electrical appliances, as well as the requirements of regulations on electrical safety. It is strictly forbidden to disassemble a device to which any conductors are connected!
Important! Although the controller has built-in protection against incorrect power connection, and in this situation will not fail, we recommend that you pay attention to the correct polarity when connecting
3. i3-NET
If your system uses multiple controllers, connect them to a i3-NET network. Install the end terminators included in the equipment kit at the ends of the bus.
4. RS-485
If you have Modbus control devices, connect them to the bus and connect them to the RS-485 connector. Install the end terminators included in the equipment kit at the ends of the bus.
5. Sensors power supply
A 3.3V controller output is provided to power the sensors.
Important! If the system uses sensors or actuators with other operating voltages, use additional power supplies or the power supply that powers the controller. If the system uses several power supplies - connect their "negative" terminals to each other.
6. Input connections
Connect sensors, switches and other devices to the controller inputs. The inputs of the controller use connectors with spring-loaded contacts, which provides convenience and reliability of connection of conductors with a cross section up to 1.5 mm2.
Atom Barium
TYPE OF INPUT / # OF INPUT
1-2
3-9
10-12
TYPE OF INPUT / # OF INPUT
TYPE OF INPUT / # OF INPUT
1-2
1-2
3-9
3-9
10-12
10-12
Analog (thermistor, photoresistor, etc.)
✖
✔
✔
TYPE OF INPUT / # OF INPUT
Analog (thermistor, photoresistor, etc.)
1-2
✖
3-9
✔
10-12
✔
Digital (motion sensors, light level sensors, switches, buttons, etc.)
✔
✔
✔
TYPE OF INPUT / # OF INPUT
Digital (motion sensors, light level sensors, switches, buttons, etc.)
1-2
✔
3-9
✔
10-12
✔
Interface (1-Wire sensors)
✔
✔
✔
TYPE OF INPUT / # OF INPUT
Interface (1-Wire sensors)
1-2
✔
3-9
✔
10-12
✔
Atom Barium N
TYPE OF INPUT / # OF INPUT
1-2
3-9
TYPE OF INPUT / # OF INPUT
TYPE OF INPUT / # OF INPUT
1-2
1-2
3-9
3-9
Analog (thermistor, photoresistor, etc.)
✖
✔
TYPE OF INPUT / # OF INPUT
Analog (thermistor, photoresistor, etc.)
1-2
✖
3-9
✔
Digital (motion sensors, light level sensors, switches, buttons, etc.)
✔
✔
TYPE OF INPUT / # OF INPUT
Digital (motion sensors, light level sensors, switches, buttons, etc.)
1-2
✔
3-9
✔
Interface (1-Wire sensors)
✔
✔
TYPE OF INPUT / # OF INPUT
Interface (1-Wire sensors)
1-2
✔
3-9
✔
Dangerous interference can occur on long lines when connecting end devices such as switches, so we use additional protection and improved sensitivity of interaction with end devices. We use optocouplers for this. By default, all inputs with jumpers are configured in this mode "Optocoupler". If you use digital sensors at the inputs of the controller, be sure to turn off this mode
Important! The inputs are numbered, and each input is marked with a "common" pin (marked with the letter "G") - this is a common contact, it is connected to the "minus" power supply of the controller. All common contacts are interconnected, so when connecting switches with a multicore cable, it is sufficient to use one connection to terminal “G”.
8. Connecting DALI devices
If you have DALI-controlled devices, connect them to the bus and connect them to the DALI connector. A suitable DALI power supply must be used to operate the bus.
Important! The maximum number of devices per bus should not exceed 64 devices.
9. Network connection (modification N)
The operation of network controllers requires remote access to configure, manage and control their operation. To ensure these capabilities, at least one of the controllers must be able to connect to a wired or wireless network. In the Atom product line, these are the N modification controllers. Don't forget to connect the network cable to the controller or configure access to the home Wi-Fi network
Important! The router must have a DHCP server configured to automatically issue the IP address and network mask.
10. Done. Turn on the power
Important! Check all connections. Make sure that the power supply, inputs and outputs are connected correctly.
11. i3 Home App configuration
After turning on the controller, you need to download the i3 Home mobile application and configure the system.
List of typical problems and their solutions
LED indicators do not light
1. Check the supply voltage on the controller2. Check the polarity of the power supply
The device is turned on but not in the application settings
1. Make sure Wi-Fi and bluetooth are turned on on your smartphone or tablet2. Verify that the home network password is specified correctly in the controller settings
Input indicators do not respond to signals from sensors or switches
1. Check that the connection is correct2. Check that the connections at the controller and sensor terminals are secure3. Check the login configuration to the type of sensor or switch
Output status indicators are not lit.
Check that the output settings are correct in the controller settings
The output status indicator lights up, the device does not turn on, or responds incorrectly
1. Check that the connection is correct and reliable2. Check the device for damage
Didn’t find the answer to your question?
You can contact the technical support chatbot.Found a mistake on the site? Help us fix it!